Z-wave Alarm Command Class -not available

Calin Birtocean

8 years ago
updated 8 years ago
Under review

Hi,

I have installed and added to Z-wave node the Carbon Monoxide Detector, ZCOMBO from First Alert.

Based on the manufacturer manual the following command classes are supported:

• BASIC

• BATTERY

• CONFIGURATION

• ASSOCIATION

• ALARM_V1

• MANUFACTURER_SPECIFIC

• VERSION

When integrated in bOS I do not see the Alarm Command Class being available. Here are the parameters that I am looking for to monitor:

Alarm Alarm Type Level

Smoke Alarm 0x01 0x00 or 0xFF

CO Alarm 0x02 0x00 or 0xFF

Malfunction Alarm 0x09 0x00 or 0xFF

Test Alarm 0x0C 0x00 or 0xFF

Heartbeat Alarm 0x0D 0xFF

CO Sensor End of Life 0x0E 0x00 or 0xFF

I was assuming to find all the alarms under "Notification" class command, but only the following are available:

The values are not changing when the Test Alarm is active(the test button is pushed).

The Battery value has changed, that's how I know the device is communicating.

The device is Associated to Controller 1.

Could you please advise if the alarms can be monitored in bOS?

Thank you,

Calin

Replies 16

Newest first
Newest first Oldest first

n muthu N Muthu

8 years ago

I have already installed BETA , but still 4.2.2

I am using NEO Siren Alarm

this device for siren and alarm and I supposed to select two different music mode for siren and alarm ,but it decided as a binary switch and I have one music for siren . alarm function not showing ( attached manual )

neo_coolcam_z_wave_siren_alarm_manual_eng.pdf

Reply Link

Quote from n muthu N Muthu

can you please send me the updated DLL to icesys@gmail.com , I have also same problem

If you install bOS Server BETA you will get the latest ComfortClick.Zwave.dll

The integration of the ZCOMBO from First Alert hasn't been solved yet. Are you experiencing issues with the same device?

Hello,

Initially I excluded the device, then update the server version to 4.4.2 and include the device.

Please send the new .dll file along with the instructions to calin.birtocean@yahoo.com

ComfortClick Support

If you could provide your email address and the new .dll file will be sent to you.

Regards.

hello,

apologies for delayed response, the missing classes were added in the new update. Did you try excluding the device and including it again? I will provide a .dll file so you can replace it with current one and see if it's working.

Could you please advise if the device was supposed to be supported in server revision 4.4.2? I tried it but still doesn't work with the device.

thank you for all the additional information you provided, we've updated our software to support these devices and a new BETA version will be available soon, which should resolve the issues you're facing. I will contact you as soon as it's available.

Best regards.

I have tested another brand new unit and I am getting the same results.

When the smoke alarm is triggered the bOS doesn't get updated. The values are not changing when the Test Alarm is activated (the test button is pushed). The only value changing is the Battery value.

Would you please take a look at the controller settings and confirm that this device(ZCOMBO) is supported in bOS.

Here are the debug logs:

2018_03_27_ZCOMBO Exclusion_Log Debug.txt

2018_03_27_ZCOMBO Inclusion_Log Debug.txt

2018_03_28_ZCOMBO Test_Silence Button Pressed_Log Debug.txt

2018_03_28_ZCOMBO Smoke Alarm Triggered_Log Debug.txt

The specification for the class commands supported is here:

Z-wave Smoke_CO detector 83852.docx

The server version is 4.4.1, the controller 1 is associated to group 1 .