I'm trying to connect a Paradox security system to a CC Grinder, through a Paradox PRT3 module USB (COM3), and I'm getting a "Error connecting to device - No Ack" message" 10 seconds after connection, keeps trying to connect.
Can't figure if its a Windows problem (tried several configurations for flow control on port settings), Paradox configuration (Serial Port ON, Automation ON, ASCII Protocol, 9600br) or CC.
Any ideas?
Thanks, Nuno! I forgot to mention I use the Colibri, which is a Raspberry Pi inside. There's not much I can do about the power saving settings. Thanks anyway!
I haven't been on this site since, because of the pandemic, but I'll be there by the end o f the month.
I believe you have a different problem, since you can establish a connection (witch I never did).
What might be happening with you is due to the power saving settings, that disconnect USB and Serial devices when not active for some time. Try to look it up.
Hi,
Did you manage to solve this?
I experineced the same issue. I set the baud rate to 2400, and then the connection was established and reporting from the PRT3 worked fine, but after a few hours it disconnected. In these cases, disabling the Paradox device, unplugging and replugging the USB and then enabling it again usually helps, but again only for a few hours.
Best,
Gabor
Hi,
Can't really help directly, but I found out a KNX module from a company called Elausys, that uses the same principle for connecting the PRT to KNX through their module, because it uses ASCII protocol as well.
Maybe the options on their manual can help...
Check the pages 6, 7, 8 and 9, they show several options to set. Maybe it can help.
https://elausys.be/wp-content/uploads/2018/07/EVO-KNX-Paradox-KNX-Interface-Manual-R2.02.pdf
Best regards
Obrigado Ricardo,
The configurations indicated for this module manual are more or less the same I have on my security module, but on the last tab, "Report Options\Messages", the first parameter (Area affected by security) is set to 0 both on the manual and my configuration. Maybe this should be set to the area i'm using, unless 0 means all. I'll have to check this.
Also noted on the Troubleshooting section they approach the same tool I stated earlier, about the Tx led not blinking. This makes me believe I'm having a problem with the Paradox system\module and not with server\windows\comfortclick.
I've seen on this forum other people having the same problem (error messages) connecting to Tv's. Maybe there's a connection, or no connection in fact :-)
Hi,
Can't really help directly, but I found out a KNX module from a company called Elausys, that uses the same principle for connecting the PRT to KNX through their module, because it uses ASCII protocol as well.
Maybe the options on their manual can help...
Check the pages 6, 7, 8 and 9, they show several options to set. Maybe it can help.
https://elausys.be/wp-content/uploads/2018/07/EVO-KNX-Paradox-KNX-Interface-Manual-R2.02.pdf
Best regards
Went back to my notes and had written that the module has 3 leds, Error (off), Rx (blinking) and Tx (off), so it still might be a problem with the security system, module or configuration.
Hello,
No I haven't.
Tried contacting Paradox Support but they only reply to distributors and asked me to contact my country distributor.
I also tried installing an Hyper Terminal emulator (Teraterm) that also couldn't get any data from the COM port. So I think it might be a problem with windows or firewall.
Also tried with other USB converter (FTDI) with the same result.
Because of the quarantine I didn't get to go back, but 'ill have to take a look in the future.
GL
Nuno
Hello,
I'm really using Babyware software from Paradox to program the security system and the APR3-PRT3 module is correctly added to the system and recognised by serial number.
The 3-digit [SECTION] programming codes for this module refer to the following parameters:
016/1 Serial Port Enabled (checked)
016/4 OFF:Send Event; ON:Residential Automation (Checked)
016/2/3 Baud Rate (9600)
016/5/6 Residential Automation (ASCII Protocol)
(in parenthesis my configuration, my translation from Portuguese - names may differ)
On the Paradox software there aren't any other parameters to configure for the serial port.
(in fact I'm using the USB port, recognised as COM3 on the Grinder Windows. Tomorrow i'll try another serial to USB adaptor on the serial port of the module)
Hello!
Have you solved this? I have the same problem..
BR!
P
Take a look here
https://www.raspberrypi.org/forums/viewtopic.php?t=35054